Friday, May 27, 2022
HomeSmall AppliancesBlendersHow To Clean Your Blender In Seconds

How To Clean Your Blender In Seconds

Learn how easy it is to clean your blender! Here, we show you the best way of cleaning a  blender literally in seconds.

 

One of the most annoying and time-consuming tasks in the kitchen is cleaning your blender. It’s a pain to take it apart, scrub all of those nooks and crannies, then put it back together again. 

 

Additionally, using the wrong products or scrubbing too hard can damage your blender blades. This can leave you with a costly repair at best and a broken appliance at worst. 

 

But there’s hope! Fewer than 30 seconds or so, your mixer can be as good as new. Here are five tips to help you clean it fast.

The Process Of Cleaning Your Blender In Seconds 

Requirements 

A blender, vinegar, dish soap. 

 

Optional: A clean towel to dry the parts after rinsing them off with water 

 

Instructions:

 

Step 1: Pour water into the blender: Fill your blender with hot water about halfway up the jar. 

 

Step 2: Add some dish soap: Add a drop of liquid dish soap to the water. The suds will help break down any stubborn food particles that are clinging onto your blender blades!

 

Step three: Turn it on! Put your blender on its highest speed setting and pulse five or six times, pausing between pulses. 

 

Step four:  Rinse it off! Turn the blender to its lowest speed setting and use a cup or bowl of vinegar to rinse everything down into your sink. You can repeat this step if you still see any food particles stuck on afterwards. 

 

And voila! There you have clean blender literary in seconds. 

 

At this point, the only thing left is drying the blender, and you’re done!

 

You can use a dry towel to dry the blender lid and glass jar. Make sure it’s completely dry so bacteria don’t grow inside the appliance.

Caution tips: Don’t use hot water on the jar because this could warp metal parts over time. Rinse the blender thoroughly after washing to remove all soap and suds. If you don’t, the residue could end up smelling funky again. 

 

Don’t use any kind of abrasive product because this might damage your blades! Wash it gently with water and a clean cloth if necessary instead. Finally, avoid using anything sharp for cleaning, such as forks or knives, because you could damage the blades.

 

Also, don’t forget to dry your blender completely after rinsing! Leaving water behind may result in mould and mildew growth which can cause funky smells over time. The last thing you want to imagine is a smelly kitchen, so it’s good practice to clean as soon as possible after use before matters get worse! 

What About Stuck On Stains?

Well, a blender cleans easily after making a smoothie. After making a thicker mixture like bisque, what remains may not be your normal kind of stuck-on particles. These are usually stubborn to remove.

 

Stubborn particles is a problem which you will have to face when cleaning blenders. The most common way of handling them is using hot water. The hot water can loosen the food particles from the blades of your blender, no doubt.

 

However, this may not completely remove the stubborn food particles from your blender. If you want to remove all of it, then use a toothbrush to reach those far areas.

 

But remember, you need to do it in seconds. Try using a baking powder- it works super fast! The magic with baking powder, as we know it, is that it makes dough rise. The same baking powder can also help to remove stubborn stains from the blender quite easily.

 

The theory behind this is that the fine particles of the baking soda will easily scrub away any food stuck on your blender’s blades. 

 

First, pour warm water into your blender jar. Then you can use about two tablespoons of powder in the water. 

 

Then run the machine at its highest speed setting to turn this into foam that will help dislodge food particles stuck on blades better than without any liquid agent. 

 

Also, the baking soda acts as a degreaser and cleans away any grease on your jar’s sides. But, you need to make sure not to let it sit for too long or else it may damage its surface. 

 

Lastly, pour another water into the blender to rinse it. Turn it back on at low speed to ensure that there’s no baking soda left in it.

Tips To Keeping Your Blender Clean

Blenders do help us to make quick work of making blends. But at the same time, they do require a little bit more attention. Here are some tips to help you keep your blender clean always: 

 

  •  Always make sure that your blades are not captured with food before blending another batch of ingredients.

 

  •  Put additional liquid during the blending process if you think this will help prevent large particles from getting stuck on its sides and blades. 

 

  • Don’t let your blender sit with leftover ingredients for too long. This can cause bacteria buildup and will become harder to clean later on.

 

  • Use a brush to reach even the most out of way areas in a jar or pitcher where food may have gotten stuck on it. However,  don’t use too much powder as this may scratch the blender’s surface.

 

  • Use the baking soda method if you want to clean all food particles from your blender deep down.

 

  • Don’t use too hot water during cleaning as this may cause discolouration. Additionally, hot water may damage the blades of your blender. 

 

Final Words 

A blender is one of those appliances that we all love but hate to clean. Luckily the above trick gives you a quick and easy way to make this daunting task as painless as possible! With this quick guide, you can get the job done fast – without having to scrub away dirt from an appliance all day! 

 

Are you using your blender on a regular basis or even once every few months? Well,  no matter how often you use it, make sure to give your machine an occasional deep-cleanse with these helpful hacks. 

 

Best part? You can do it literally in seconds!

RELATED ARTICLES
- Advertisment -
Google search engine

Most Popular

Recent Comments